联系我们
公司名称：XXX
电话：XXX
手机：XXX
联系人：XXX
地址：XXX
新闻动态
自动门电机门机安装：
自动门电机门机安装：
Installation of automatic door motor and door operator:
1、墙壁安装，安装前必须将墙面整平，以免不平造成轨道弯曲与产生噪音。导轨安装面平整度应小于1、5mm墙体安装可用膨胀螺丝将导轨打孔固定，间隔为35-45cm之间。
1. For wall installation, the wall must be leveled before installation to avoid uneven track bending and noise. The flatness of the guide rail mounting surface should be less than 1. 5 mm. For wall installation, the guide rail can be fixed with expansion screws at an interval of 35-45 cm.
2、槽钢与角铁架安装时可直接用平头螺丝或自功螺丝固定，间隔可与上相同，垂直1-2个。
2. When installing the channel steel and angle iron frame, they can be directly fixed with flat head screws or self powered screws, and the spacing can be the same as above, 1-2 vertically.
3、安装驱动轨道前，先用透明水管充满水之(管中不可有)测定导轨两端及中间水平度，地面以 高点为准。
3. Before installing the drive rail, first fill it with water (not allowed in the pipe) and measure the levelness of both ends and the middle of the rail. The ground shall be subject to the high point.
4、将导轨螺丝孔打好，再将导轨两端各暂时用一支螺丝固定在墙面或钢结构上，再次校正水平后确认准确再增加固定。注意：导轨以门体上升一般以25mm为准确。(根据机型而定)
4. Drill the screw holes of the guide rail, and then temporarily fix the two ends of the guide rail on the wall or steel structure with a screw. After correcting the level again, confirm that it is accurate and then increase the fixation. Note: The guide rail is generally accurate at 25mm when the door body rises. (depending on the model)
5、自动门传感器应先州苗木 保定通风管道 丝网立柱模具 尼龙输送带 保定防水 保定空压机 高碑店养老院装外面一点，一般装在门洞正中央之上方，高度根据现场情况而定。接线先参考说明书。
5. The automatic door sensor should be installed outside first, generally above the center of the door opening, and the height depends on the site situation. Refer to the manual for wiring.
6、安装电动部件前先将导轨清理干净，再将马达、电盘、尾轮、变压器分别装在轨道固定槽内，把它移到适当位置，安装定位凝聚固定螺丝。
6. Clean the guide rail before installing the electric parts, then install the motor, electric panel, tail wheel and transformer in the track fixing slot, move it to the appropriate position, and install the positioning and condensation fixing screws.
Installation of automatic door motor and door operator:
1、墙壁安装，安装前必须将墙面整平，以免不平造成轨道弯曲与产生噪音。导轨安装面平整度应小于1、5mm墙体安装可用膨胀螺丝将导轨打孔固定，间隔为35-45cm之间。
1. For wall installation, the wall must be leveled before installation to avoid uneven track bending and noise. The flatness of the guide rail mounting surface should be less than 1. 5 mm. For wall installation, the guide rail can be fixed with expansion screws at an interval of 35-45 cm.
2、槽钢与角铁架安装时可直接用平头螺丝或自功螺丝固定，间隔可与上相同，垂直1-2个。
2. When installing the channel steel and angle iron frame, they can be directly fixed with flat head screws or self powered screws, and the spacing can be the same as above, 1-2 vertically.
3、安装驱动轨道前，先用透明水管充满水之(管中不可有)测定导轨两端及中间水平度，地面以 高点为准。
3. Before installing the drive rail, first fill it with water (not allowed in the pipe) and measure the levelness of both ends and the middle of the rail. The ground shall be subject to the high point.
4、将导轨螺丝孔打好，再将导轨两端各暂时用一支螺丝固定在墙面或钢结构上，再次校正水平后确认准确再增加固定。注意：导轨以门体上升一般以25mm为准确。(根据机型而定)
4. Drill the screw holes of the guide rail, and then temporarily fix the two ends of the guide rail on the wall or steel structure with a screw. After correcting the level again, confirm that it is accurate and then increase the fixation. Note: The guide rail is generally accurate at 25mm when the door body rises. (depending on the model)
5、自动门传感器应先州苗木 保定通风管道 丝网立柱模具 尼龙输送带 保定防水 保定空压机 高碑店养老院装外面一点，一般装在门洞正中央之上方，高度根据现场情况而定。接线先参考说明书。
5. The automatic door sensor should be installed outside first, generally above the center of the door opening, and the height depends on the site situation. Refer to the manual for wiring.
6、安装电动部件前先将导轨清理干净，再将马达、电盘、尾轮、变压器分别装在轨道固定槽内，把它移到适当位置，安装定位凝聚固定螺丝。
6. Clean the guide rail before installing the electric parts, then install the motor, electric panel, tail wheel and transformer in the track fixing slot, move it to the appropriate position, and install the positioning and condensation fixing screws.
